Honda Goldwing Forums - Reply to Topic
Thread: Rear LED turn signals Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Honda Goldwing Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
05-03-2018 04:00 AM
Jinx
Quote:
Originally Posted by Rusty360 View Post
I have heard that switching the bulbs around in the socket helps with other issues might be worth a try.
Tried that nogo.

Quote:
Originally Posted by NREMTP View Post
Have you measured the voltage at the light connectors? I have no idea how sensitive your LEDs are to very low voltages but you might want to check that out so you can rule out any inductive coupling from adjacent wires in the loom. Like Daryl said, a resistor might be needed.

My gut says that this is a grounding issue. Whenever I get weird electrical stuff happening, that is usually the cause but LEDs are special.
These same LEDs worked great in my 2006 as well as two other bikes. The voltages stated in my first post were measured at the
tail light harness connector with the bulb plugged into it bypassing the bulb adapter.

The ground issue was my thought too. That is why I connected a good ground to each bulb. My technical background tells me it
is a bad component in the signalling circuit.

Although the resistor solution may solve the problem my OCD wont allow me to do that.

This may just have to be added to my winter project list.
05-02-2018 08:20 PM
Rusty360 I have heard that switching the bulbs around in the socket helps with other issues might be worth a try.
05-02-2018 07:36 PM
NREMTP Have you measured the voltage at the light connectors? I have no idea how sensitive your LEDs are to very low voltages but you might want to check that out so you can rule out any inductive coupling from adjacent wires in the loom. Like Daryl said, a resistor might be needed.

My gut says that this is a grounding issue. Whenever I get weird electrical stuff happening, that is usually the cause but LEDs are special.
05-02-2018 01:45 PM
Jinx If you are talking about the hyper flash that has been taken care of.

Thank you for your responce.
05-02-2018 12:36 PM
budoka I'm no expert on LEDs but without the proper capacitors/resistors there can be voltage issues and that's what it sounds like to me. Hopefully some of our LED conversion gurus can chime in and help.
04-25-2018 11:16 AM
Jinx
Rear LED turn signals

It appears from the manual that 2015 - 2017 wing have some electrical differences from the 2012-2014 so this question is for the 2015 and up owners.

Trying to install LED turn signals in the rear of my 2017 gl1800 in place of the oem bulbs but have a stranger issue. When I turn on the blinkers and then off one of the rear turn signals stays on dimly. If I use the left blinker the left rear will stay on dimly, if I then turn the right side on when it goes off the right rear will be dimly light. If I the turn the ign to ACC and turn on the hazard lights and then turn then off the the rear blinker that was last used will
be dimly lit. I measured the voltage and when the lift stays on it is at 4.5v and the right is at 0v. When the right stay on it has 2.5v on it and the left has 0v. I have connected a gnd wire directly to the gnd side and the frame without any change. Also measured the gnd side of each socket and it seems good.

The oem bulbs work just fine.

Has anyone installed LED turn signals had this problem or does anyone have any suggestions as to what might be the issue.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome